Loading...
05-50 - O TOWN OF PROSPER, TEXAS ORDINANCE NO: 05-50 AN ORDINANCE OF THE TOWN OF PROSPER, TEXAS, ESTABLISHING THOROUGHFARE AND CIRCULATION DESIGN REQUIREMENTS FOR THE PURPOSE OF PROMOTING THE HEALTH, SAFETY, AND WELFARE OF THE TOWN AND ITS RESIDENTS; PROVIDING FOR A PENALTY FOR THE VIOLATION OF THIS ORDINANCE; PROVIDING FOR REPEALING, SAVINGS AND SEVERABILITY CLAUSES; PROVIDING FOR AN EFFECTIVE DATE OF THIS ORDINANCE. WHEREAS, the Town Council of the Town of Prosper, Texas ("Town Council") has investigated and determined that it will be advantageous and beneficial to the Town of Prosper, Texas ("Prosper") and its inhabitants to establish Thoroughfare and Circulation Design Requirements as set forth below; and WHEREAS, the Town Council has further investigated and determined that Prosper has complied with all legal requirements in adopting this Ordinance. NOW, THEREFORE, BE IT ORDAINED BY THE TOWN COUNCIL OF THE TOWN OF PROSPER, TEXAS: SECTION 1: Findings Incorporated. The findings set forth above are incorporated into the body of this Ordinance as if fully set forth herein. SECTION 2: Establishment of Thoroughfare and Circulation Design Requirements. There are hereby created and established within Prosper the Thoroughfare and Circulation Design Requirements for the purpose of promoting the health, safety, and welfare of Prosper and its inhabitants. The Thoroughfare and Circulation Design Requirements are hereby established as set forth in Exhibit A, attached hereto and incorporated for all purposes. SECTION 3: Penalty Provision: Any person, firm, corporation or business entity violating this Ordinance, or as amended, shall be deemed guilty of a misdemeanor, and upon conviction thereof shall be fined a sum not exceeding Five Hundred Dollars ($500.00). Each continuing day's violation under this Ordinance shall constitute a separate offense. The penal provisions imposed under this Ordinance shall not preclude Prosper from filing suit to enjoin the violation. Prosper retains all legal rights and remedies available to it pursuant to local,state and federal law SECTION 4: Savinqs/Repealinq Clause: Should any part of this Ordinance be declared unconstitutional or invalid by a court of competent jurisdiction, it is expressly provided that any and all remaining portions of this Ordinance shall remain in full force and effect. All provisions of any ordinance in conflict with this Ordinance are hereby repealed; but such repeal shall not abate any pending prosecution for violation of the repealed ordinance, nor shall the repeal prevent a prosecution from being commenced for any violation if occurring prior to the repeal of the Ordinance. SECTION 5: Severability: Should any section, subsection, sentence, clause or phrase of this Ordinance be declared unconstitutional or invalid by a court of competent jurisdiction, it is expressly provided that any and all remaining portions of this Ordinance shall remain in full force and effect. Prosper hereby declares that it would have passed this Ordinance, and each section, subsection, clause or phrase thereof irrespective of the fact that any one or more sections,subsections,sentences, clauses and/or phrases be declared unconstitutional or invalid. SECTION 6: Effective Date: This Ordinance shall become effective upon its passage and publication as required by law. DULY PASSED AND APPROVED BY THE TOWN COUNCIL OF THE TOWN OF PROSPER, TEXAS on this 14th day of June, 2005. APPROVED AST .• Charles Nis nger, May ATTE ED TO AND CORRECTLY RECORDED BY: Shanae Jennings, n Secretary DATE OF PUBLICATION: frY403-- d,/U 'J ballas Morning News—Collin County Addition Exhibit A SECTION 1 TOWN OF PROSPER THOROUGHFARE AND CIRCULATION DESIGN REQUIREMENTS SECTION 1 - THOROUGHFARE AND CIRCULATION DESIGN REQUIREMENTS 1.01 GENERAL: A. The arrangement, character, extent, width and location of all streets shall be in conformity with the Town's Thoroughfare Plan and Comprehensive Plan, and should be considered in their relation to existing and planned streets, topographical and environmental considerations, scenic views and the land uses proposed to be served by such streets. B. In the interpretation and application of the provisions of these standards, it is the intention of the Town Council that the principles, standards and requirements provided herein shall be minimum requirements for the development of property in the Town of Prosper, and where other ordinances of the Town are more restrictive, such other ordinances shall control. C. All deviations from the provisions presented herein shall be approved by the Prosper Town Staff which includes, the Town Administrator, Town Engineer, Director of Planning and Development Services, Director of Public Works, Building Official, Town Fire Chief, and any others deemed necessary by the Town Administrator. 1.02 STREET DESIGN: A. Thoroughfare Definitions - The Town of Prosper recognizes four basic classifications of public roadways that include freeways, thoroughfares, collectors, and local streets as identified in the transportation element of the Comprehensive Plan. Each class provides a certain degree of continuity, capacity, and accessibility to adjacent land uses. While differentiated by function, there is also a variance in geometric design. Table 1.1 summarizes the general design criteria of roadways within Prosper. The typical cross-sections are depicted in Figures 1.1 through 1.4. B. Roadway Geometrics - Geometrics of city streets may be defined as the geometry of the pavement and curb areas that govern the movement of traffic within the confines of the rights-of- way (ROW). Included in the geometrics are pavement width, degree of curvature, width of traffic lanes, median nose radii, curb radii at street intersections, cross fall, crown height, pavement thickness and geometric shapes of islands separating traffic movements and other features. 1. Design Speed - The design speed is a primary factor in the horizontal and vertical alignment of roadways. Design features such as curvature, super-elevation, turning movement radii and sight distance affects roadway lane width, pavement width, pavement cross-fall, pavement crown and clearances. The design speeds depicted shall be used where existing ground slopes are less than six percent (6%). Refer to Table 1.1. 2. Grades - Roadway grades shall be a minimum of six-tenths percent (0.6%) in order to insure proper flow of surface drainage toward inlets and a maximum of six percent (6%). Steeper grades may be permitted on local residential streets and where required by topographical features, as approved by the Town Engineer or his/her designee. 3. Roadway Centerline - Roadways shall be placed in the center of the ROW, but may be shifted slightly to avoid groupings of trees. The centerline of curves shall be tangent to the centerline of street at each end of curve. 4. Cross Fall/Crown Height— 6LD and 4LD thoroughfares shall have a minimum cross fall of one- quarter inch per foot and a maximum cross fall of three-eighths inch per foot. 3L and 2LC thoroughfares shall have six-inch (6") parabolic crowns, and 2LN and 2LRN thoroughfares a five-inch (5") parabolic crown. 1-1 5. Pavement Thickness - All pavement and six-inch (6") integral curb shall be a minimum 3500psi with #3 bars twenty-four inch (24") on center. Six inches (6") minimum of lime stabilized subgrade to reduce Plasticity Index (PI) to fifteen (15) as determined by lime series. Add one-percent (1%) for field variation. Refer to Table 1.1 for pavement thickness. If solid rock is present, waiver of lime stabilized subgrade may be approved by the Town Engineer. TABLE 1.1: Town of Prosper Thoroughfare Definitions Thoroughfare Class Criteria Ultimate Interim Minor Minor Comm. Collector Local Major Major(2) Rural 4LD Couplet 2LC 2LN/ 6LD 4/6LD 4LRD 3L Com/Res 2LRN Right-of-Way (ROW) 120'(5) 12045) 110' min. 90'(6) 65' 60' 50'/50'min. Pavement Width (face to face) 2 @ 36' 2 @ 24' 2 @ 24' 2 @ 24' 5343) 3648) 30'/26' Traffic Lanes 6 4 4 4 2 2 2 Shoulder Width -- -- 8' -- -- -- --/ 2' Left Turn-lane Width 2 @ 10' 1 @ 12' 1 @ 10' 1 @ 10' -- -- -- Right Turn-lane Width 11' 11' 10' 11' -- -- -- Median Width 24' 48' 16' 18' -- -- -- Parkway Width 12' 12' -- 12' 6'sidewalk 12' 12'/ -- Ditch Width -- -- 15'min. -- -- -- --/ 10'min. Minimum Pavement Thickness(7) 8" 8" 8" 8" 7" 7" 7" Design Speed, V(MPH) 50 50 45 45 30 30 25 Minimum Grade 0.6% 0.6% 0.6% 0.6% 0.6% 0.6% 0.6% Maximum Grade 6% 6% 6% 6% 6% 6% 6% Min. Horizontal Radii(') 1,400' 1,400' 1,100' 1,100' 450' 450' 300" Min. Tangent Between Curves 100' 100' 100' 100' 100' 100' -- Min. Length of Crest Curve See Table 1.3 Min. Length of Sag See Table 1.4 Stopping Sight Distance 425' 425' 360' 360' 200' 200' 155' Parking None None None None Permitted Permitted Permitted Volume Range (VPD) 36-45,000 20-28,000 20-28,000 20-28,000 12-18,000 6-12,000 -- (1) Absolute minimum based on —2% cross slope. (2) Four lane thoroughfare built in ROW of a 6-lane 6LD thoroughfare so it can be widened in the future. (3) Pavement of Commercial Couplet 3L includes 37'of travelway with 8'of parking on either side. (4) May be reduced to two hundred feet (200') radius at mid-block locations provided that it is shown that the general public safety is not compromised. A curve, with a radius less than two hundred fifty feet (250'), must be a minimum of three hundred feet (300') from a street or alley intersection. (5) 140' ROW at intersections with a 4 or 6 lane thoroughfare. (6) 110' ROW at intersections with a 4 or 6 lane thoroughfare. (7) Thickness shall be based on the geotechnical soils report. (8) Roadways adjacent to a neighborhood park or school shall have a minimum pavement width of 36 feet. C. Minimum Horizontal Design Radius: 1. The minimum centerline radius is a function of design speed, super-elevation and vehicle side friction. Side friction is the force that keeps a vehicle from sliding off of the roadway. The minimum acceptable horizontal centerline radius is calculated using the following equation: VZ R(ft.)= 15(e+f) where: R = centerline radius (ft); V = vehicle design speed (MPH); e = rate of roadway super- elevation, (ft/ft); f= side friction factor. 1-2 Ultimate Major Thoroughfare '6LD' (Intersection) 3- 140' ' d 107 3 11' p 22' PKWY. PKWY. , 36' > 24'MEDIAN 47 `c4 10'LEFT 10'LEFT 2' i 12' 12' i 12' TURN> TURN c 12 12' 12' > 11' ) 2'0. .--4-_ THRU THRU THRU ' ' /� �P THRU THRU THRU RIGHT �'- 4'SIDEWALK 4'SIDEWALK Ultimate Major Thoroughfare '6LD' (Midblock) 3 120' O 96' > 12' 12' O PKWY. 36' 24'MEDIAN - 36' , PKWY.yri 2' 12' , 12' > 12' . 12' 12' > . 12' 4. - <2' THRU THRU THRU THRU THRU THRU 4'SIDEWALK 4'SIDEWALK if Interim Major Thoroughfare '4/6LD' (Intersection) 3, 140' —.. 107' d 22' 1I' PKWY. u PKWY. , < 24' 48'MEDIAN 35' > a 12'LEFT 2' . 12' > Q � 12' <TURN < 12' 12' - 11' 2'_ • THRU THRU Q ' THRU THRU RIGHT �� 9 -- TURN - 4'SIDEWALK 4'SIDEWALK 1 Interim Major Thoroughfare '4/6LD' (Midblock) 3 120' O 96' . 1 a 2'<PKWY. 24' 48'MEDIAN 24' ' ,PKWY...n% 2' , 12' > , 12' ,, , 15' 15' < 12' > < 12' -2' THRU THRU CLEAR CLEAR > ZONE ZONE THRU THRU C 4'SIDEWALK 4'SIDEWALK 1 FIGURE 1.1: Cross Sections for 6LD and 4/6LD Thoroughfares 1-3 Minor Thoroughfare '4LD' (Intersection) . 1Io'0 22' , 77' n' 0 a c PKWY. > < 24' _<18'MEDIAN , 35' PKWY,a 10'LEFT 2' 12' 12 TURN < 12' 12 , 11' ' 2' THRU THRU THRU T U RIGHTGH 4'SIDEWALK 4'SIDEWALK Minor Thoroughfare '4LD' (Midblock) 90' 3 ` 66' 3 O PKWY. 24' 18'MEDIAN • 24' PKWY. 2' 12' 12' 12' 12' 2' THRU THRU� Q Q THRU THRU 4'SIDEWALK 4'SIDEWALK Minor Rural Thoroughfare '4LRD' (Intersection) 110'Minimum* 3 ` 64' 3 24' 16'MEDIAN 24' a * 8' 10'LEFT 15'Minimum 11' 11' 10' 15'Minimum* 12' > . 12' <TiJR11>< , - >THRU THRU Q ' ' ,IC> SHLDR 0 THRU THRU RIGHT DITCH ' TURN DITCH • • Minor Rural Thoroughfare '4LRD' (Midblock) 110'Minimum* 3- 10' 64' 10' ' 3 O CLEAR' 'CLEAR a, ZONE 24' <16'MEDIAN 24' ZONE O >H > '1 rx 15'Minimum* 8' 12' 12' 12' 12' 8' 15'Minimum* THRU THRU SHLDR 0. U U SHLDR DITCH ' DITCH *Varies depending on drainage area calculations. FIGURE 1.2: Cross Sections for 4LD and 4LRD Thoroughfares 1-4 Commercial Couplet '3L' < 65' . d < 37' ,. aC 6' 8' 12' 13' 12' 8' 6' SIDE PAR. THRU Q PAR. SIDE WALI4PARK . . ,� THRU PARK WALK _--r CENTER �— LANE Collector Street '2LC' (Commercial and Residential) . 60' . 12' 12' [ PKWY.> f 36' PKWY. 1:4• 2' 18' 18' 2' THRU THRU —1 4'SIDEWALK i 4'SIDEWALK Neighborhood Street '2LN' 3 50' O f 10' 10' O oG PKWY. 30' PKWY. a 2' < 15' 15' - < 2' THRU THRU — L 4'SIDEWALK 4'SIDEWALK Rural Neighborhood Street '2LRN' 50'Minimum* O CLEAR ZONE CLEAR ZONE *O d 10' 26' 10' a 10'Minimum*...2' 13' 13' 2' 10'Minimum' [ 4 f ) 1 l y I Q 12a q THRU THRU = D�u `n D� 'Varies depending on drainage area calculations. FIGURE 1.3: Cross Sections for 3L, 2LC, 2LN, and 2LRN Thoroughfares 1-5 Divided Residential Subdivision Entrance ss • 3 61' 0 12' 12' O P= PKWY. 24' 13'MEDIAN 24' PKWY. 2 2' THRU _ THRU r 4'SIDEWALK 4'SIDEWALK FIGURE 1.4: Cross Section for Divided Residential Subdivision Entrance 2. The minimum acceptable horizontal radius is shown in Table 1.2. The maximum length of a horizontal curve on 3L, 2LC, 2LN, and 2LRN thoroughfares shall not exceed 1.6 times the centerline radius for a radius of two hundred feet(200') or greater. TABLE 1.2: Minimum Horizontal Centerline Radius Design Speed f ft/ft R(ft) e( )V(MPH) (Rounded for Design) 25 0.165 -0.02 300(1) 30 0.160 -0.02 450 35 0.155 -0.02 600 40 0.150 -0.02 850 45 0.145 -0.02 1,100 50 0.140 -0.02 1,400 (1) May be reduced to two hundred feet (200') radius at mid-block locations provided that it is shown that the general public safety is not compromised. A curve, with a radius less than two hundred fifty feet (250'), must be a minimum of three hundred feet (300') from a street or alley intersection. D. Minimum Vertical Alignment: 1. Vertical curves are utilized in roadway design to affect gradual change between tangent grades and will result in a design which is safe, comfortable in operation, pleasing in appearance and adequate for drainage. Vertical curve alignment shall also provide Stopping Sight Distance (SSD) in all cases. SSD is a function of design speed, perception-reaction time, grade, and vehicle deceleration. The perception-reaction time is assumed to be 2.5 seconds as stated by American Association of State Highway and Transportation Officials (AASHTO). The vehicle deceleration is assumed to be 11.2 feet per second per second (fps2) based upon conservative pavement conditions and the ability of a vehicle to decelerate on a level grade. The equation for SSD appears below: SSD = 1.47PV+1.075 v2 a where: SSD = Stopping Sight Distance (ft); P = Perception Reaction Time (2.5 sec.); V = vehicle design speed (MPH); a = vehicle deceleration rate (11.2 fps2) 1-6 2. The minimum acceptable length of Crest and Sag curves are shown in Tables 1.3 and 1.4. Tables 1.3 and 1.4 also show values of K. K is defined as the rate of vertical curvature and is equivalent to the horizontal distance in feet required to make a one percent (1%) change in grade. The values of A are equivalent to the algebraic difference in grade between the two grades that are being joined together by the vertical curve. TABLE 1.3: Minimum Acceptable Crest Curve Given Speed and Difference in Grade of Road Design SSD Length of Vertical Curve, ft(L=KA) Speed, K (ft) V(MPH) A=1(1) A=2 A=3 A=4 A=5 A=6 A=7 A=8 A=9 A=10 25 155 I 12 -- 100 100 100 100 100 100 100 110 120 30 200 19 -- 100 100 100 100 120 140 150 170 190 35 250 29 -- 100 100 120 150 180 200 230 260 290 40 305 44 100 100 130 180 220 270 310 350 400 440 45 360 61 100 120 180 250 310 370 430 490 550 610 50 425 84 100 170 250 340 420 510 590 670 760 840 (1) Speeds less than forty miles per hour (40MPH), no vertical curve is necessary. Speeds greater than forty miles per hour (40MPH), use length of one hundred feet (100'). TABLE 1.4: Minimum Acceptable Sag Curve Given Speed and Difference in Grade of Road Design SSD Length of Vertical Curve, ft(L=KA) Speed, K V(MPH) (ft) A=1(1) A=2 A=3 A=4 A=5 A=6 A=7 A=8 A=9 A=10 25 155 26 -- 100 100 110 130 160 180 210 240 260 30 200 37 -- 100 110 150 190 220 260 300 330 370 35 250 49 -- 100 150 200 250 300 340 390 440 490 40 305 64 100 130 190 260 320 390 450 510 580 640 45 360 79 100 160 240 320 400 480 550 630 710 790 50 425 96 100 190 290 390 480 580 670 770 870 960 (1) Speeds less than forty miles per hour (40MPH), no vertical curve is necessary. Speeds greater than forty miles per hour (40MPH), use length of one hundred feet (100'). E. Standard Intersection Layout: 1. Street intersections shall intersect at ninety degree (90°) angles. Intersection approaches for 4 or 6 lane thoroughfares shall remain perpendicular for a minimum distance equal to the corresponding design speed Stopping Sight Distance (SSD) identified in Table 1.3. For residential collector and/or local street intersections, a five degree (5°) tolerance is allowable. 2. The curb radii shall be twenty feet (20') where 2 lane thoroughfares intersect with other 2 lane thoroughfares. All other intersecting streets, curb radii shall be thirty feet (30'). 3. Intersections of 4 or 6 lane thoroughfares with other 4 or 6 lane thoroughfares shall maintain a maximum slope of two percent (2%) a minimum distance of two hundred feet (200') upstream and downstream of the intersection. 4. Roadway connections to a 4 or 6 lane thoroughfare shall maintain a maximum slope of two percent (2%) a minimum distance of one hundred feet (100') upstream and downstream of the intersection. 1-7 5. A separate grading plan shall be provided for intersections of 4 or 6 lane thoroughfares with other 4 or 6 lane thoroughfares. 6. At four-way intersections of parabolic streets, the reduction of the crown height shall occur on the thoroughfare with the through gutter. a. For 3L and 2LC thoroughfares, the crown height reduction from six inches (6") to three inches (3") shall occur through the intersection and transition from the curb return to a point fifty feet (50') past the curb return. b. For 2LN and 2LRN thoroughfares, the crown height reduction from five inches (5") to three inches (3") shall occur through the intersection and transition from curb return to a point thirty feet(30') past the curb return. 7. Alley curb radii shall be fifteen feet (15'). 8. A minimum of nine and a half feet (9.5') of parkway shall be maintained from the back of the curb along the curb's radius. 9. ROW width for a 6LD or 4/6LD thoroughfare that intersects a 4 or 6 lane thoroughfare shall be one hundred forty feet (140') for a distance of two hundred feet (200') from the intersection and then taper at a 15:1 ratio to the standard ROW width. This allows for the future construction of additional traffic lanes at the intersection. See Figure 1.5. 6LD or 4/6LD Thoroughfare 150 Ft.with 200 Ft. a 15:1 Taper w _ _ _ 12' Pkwy en - c 11' Pkwy F"' 140 Ft. ROW 120 Ft. ROW af 12' Pkwy ( J 22' Pkwy — — ! — — O 1 150 Ft.with 200 Ft. a 15:1 Taper FIGURE 1.5: Major Intersection Detail 10. ROW width for a 4LD thoroughfare that intersects a 4 or 6 lane thoroughfare shall be one hundred ten feet (110') for a distance of one hundred fifty feet (150') from the intersection and then taper at a 15:1 ratio to the standard ROW width to allow build-out of the intersection. See Figure 1.6. 1-8 4LD Thoroughfare 150 Ft. with 150 Ft. a 15:1 Taper w ` — _ Ow- 12' Pkwy s 11 0 Ft ROW 11' Pkwy 90 Ft. ROW 1 /1 22' Pkwy _ _ _ _ — 112' Pkwy c I 150 Ft. with 71. l� 150 Ft. a 15:1 Taper FIGURE 1.6: Minor Intersection Detail F. Residential Frontage - Residential units, except for multifamily and townhome units, shall not front or side a 6LD, 4/6LD, 4LD, 4LRD, 3L, or Commerical 2LC thoroughfare unless parallel access roads are provided. Minimum distances between adjacent curbs of the thoroughfare and the access road shall be twenty feet (20'). Access road ROW shall be in addition to the thoroughfare ROW and shall not connect to the adjacent thoroughfare. G. Bike Lane Consideration — If a thoroughfare is designated as a bike route, the width of the outside lane and the width of the ROW shall be increased by three feet (3') on 4 or 6 lane thoroughfares. For federal funding, five feet (5') may be required. 1.03 MEDIAN, LEFT-TURN LANE, RIGHT-TURN LANE, DECELERATION LANE AND ISLAND DESIGN: A. Required Median Openings and Left-Turn Lanes: 1. Median openings on divided thoroughfares shall be required at all street intersections. Median openings may be constructed to serve non-residential drives provided that the minimum spacing requirements listed are met. Left-turn lanes shall be provided at all median openings. 2. All non-residential lots on a divided thoroughfare shall have direct or indirect access to a median opening. Indirect access shall be provided through a series of fire lane and access easements. Multifamily developments, on a divided thoroughfare, shall have direct access to a median opening. Median openings for street intersections and non-residential driveways may be moved at the discretion of the Town to facilitate traffic flow as long as minimum distances are maintained as per Sections 1.03.(B.4) and 1.03.(B.5). B. Minimum Left-Turn Storage, Transition Length, and Median Opening Width, Location, and Spacing Requirements: 1. Left-Turn Lane Storage: a. All left-turn storage areas on divided thoroughfares shall be ten feet (10') wide. b. Storage requirements listed in Table 1.5 are absolute minimums. Storage requirements may be increased by the Town based upon actual and projected traffic demands of the properties, which will be served by the left turn lane. 1-9 c. Left-turn lanes will be delineated by using buttons. d. Concrete pavers shall be used in the median rather than grass when the median width measured from back of curb to back of curb is a distance of four feet(4') or less. 2. Transition Length - The transition specifications for left-turn lane entrance areas are specified in Table 1.5. The variables used for the specification are shown in Figure 1.7. 3. Median Openings: a. Median openings at intersections shall accommodate all turning paths and crosswalks. b. The length of mid-block median openings shall be between sixty feet (60') and seventy feet (70'). Median openings may be up to eighty feet (80') long where necessary to accommodate turning paths and crosswalks, subject to approval by the Town Engineer or his/her designee. 4. Minimum Spacing Between an Intersection and the First Mid-Block Median Opening on Divided Thoroughfares -The minimum distance to the first mid-block median opening along 4 or 6 lane thoroughfares that are immediately downstream from an intersection with a 4 or 6 lane thoroughfare are shown in Figure 1.8. These distances vary from three hundred fifty feet (350') to four hundred feet (425') nose to nose depending on the thoroughfare type and the type of mid-block opening. TABLE 1.5: Minimum Left-Turn Lane Design Requirements Type of Type of Turn Lane Length of Transition Specifications Thoroughfare Thoroughfare Width(s) Full-Width On At (ft) Turn Len th ft RAM R2(ft) Lane(ft) g ( ) 6LD, 4/6LD _ 4 or 6 lane 10(1) 150,250(2) 200 505 505 4LD, 4LRD 4 or 6 lane 10 150 100 250 250 4 or 6 lane 3L, 2LC 10 150 100 250 250 4 or 6 lane 2LN, 2LRN 10 100(3) 100 250 250 4 or 6 lane Non Residential 10 150 100 250 250 Driveway NTTA Service All Types 10 150,250(2) 200 505 505 Road (1) Double Left-Turn Lanes (2) 150'—Inside Left-Turn Lane; 250'—Outside Left-Turn Lane (3) 150'stacking shall be required for gated communities. 1-10 Length of Storage Length Transition Lane Width R1 Concrete Pavers R 2 FIGURE 1.7: Typical Left-Turn Lane Dimensions 1-11 6LD or 4/6LD Thoroughfare (Dual Left Turn) se w 'r1 w zr5 425 Ft.Overall 0 0 ., L 150 Ft.Storage —_ 200 Ft.Transition e r O. 0 " n CO 3 a o a a O '. d IQ = O L ! m F O 100 Ft. to A Transition ��es 150 Ft.Storage — seco C to m 6LD or 4/6LD Thoroughfare N a (Dual Left Turn) r, 7 L 400 Ft.Overall 0.- N d bD i o• _ 150 Ft Storage __ 200 Ft.Transition L'" o I C:s'0 0 0 A 4p 100 Ft. 100 FL C o Storage n o Transition �� g S% • -eo O >n 4/6LD,4LD, or 4LRD Thoroughfare (Single Left Turn) 400 Ft.Overall w - zra w 0 ; s 100 Ft. •WO I50 Ft.Storage Transition N o -.IFa► en9. ▪ CO s Co 0' 0 • 9 C pp O O el C 0 A 3. 0 E. 0 100 FL fD ego dq • Transtion sot---to 150FL Storage m G c m m 4/6LD,4LD,or 4LRD Thoroughfare (Single Left Turn) N St P. 350 FL Overall =ad 100 Ft. 6. G _ 150 Ft.Storage __ Transition Ina 9. L O n E•■ 1-3 C o 'O se 100 FL 100 Ft. p A o vo Transition /11.-.111 Storage C LT CleL p'CIO O m O 7 A 'S FIGURE 1.8: Minimum Spacing Between an Intersection and the First Mid-Block Median Opening on a Divided Thoroughfare. 1-12 5. Minimum Distance Between Mid-Block Median Openings for 3L, 2LC, 2LN, and 2LRN Thoroughfares and Driveways along Divided Thoroughfares - The minimum distance between median openings on a 4 or 6 lane thoroughfare where left-turn storage is provided in both directions for 3L, 2LC, 2LN, and 2LRN intersecting thoroughfares and driveways is shown in Figure 1.9. The distances shown are measured nose to nose. Refer to Table 1.10 for driveway design requirements. czt 4 or 6 Lane Thoroughfare 6. y 3 400 Ft.Overall t� a° L C~ ,tw ? o o 0 = L 100 Ft. 0 "S p; 0 =A f 150 Ft.Storage - _ Transition C" CO C. i `,. 2 n O -4 ^o \ L 4- o O o A, c g r4 U,-414 o a ^o 0 o d ,-4 z 100 Ft. CD ,9 en Transtion .� 150 Ft.Storage _ � a 4, czt c 4 or 6 Lane Thoroughfare N 1.1— - • ' f 350 Ft.Overall C ce L `t 1 l00 Ft. N Cd 4 150 Ft.Storage Transition _ r ei o O Cor i- b 7 yb cU � J o0 1 (NI• �� 100 Ft. 100 Ft. C . cfQ .r p Z Transition �� Storage — 0" O -s Mkt A cv 4 or 6 Lane Thoroughfare N et cp — 300 Ft.Overall Z O i tt 100 Ft 100 Ft. "t tic cu -0 CI_� Transition r n �- O © p 0 C . 01 L, 100 Ft. 100 Ft. 0 Cfq O Z — Transition _ Storage co• FIGURE 1.9: Minimum Distance Between Mid-Block Median Openings on a 4 or 6 Lane Thoroughfare 1-13 6. Medians Where No Left-Turn Lane is Needed: a. The minimum length of median shall be the sum of the required left-turn storage, transition length, ten-foot (10') tangent and length of median nose. This requirement is reflected in Figure 1.10. This is allowed, provided that access is not compromised for vacant property on the opposite side of the street. 10' Storage Length Transition Tangent Pi° 111110""- 7114-- FIGURE 1.10: Minimum Length of Median Where No Left-Turn Lane is Needed b. If left-turn storage is not required in either direction, and the median is simply a spacer between two median openings, the minimum length of the spacer must be one hundred feet(100') (see Figure 1.11). 100 Ft.Minimum Spacer I"; 1 E cj FIGURE 1.11: Minimum Spacer Length c. If a driveway is not served by a median opening, then seventy-five feet (75') of separation shall be provided from the edge of driveway to the nearest median opening. 7. Medians on Public Street Entrances to Developments: a. Medians installed on undivided streets at entrances to subdivisions for aesthetic or any other purpose shall be a minimum of thirteen feet (13') wide and one hundred feet (100') long (See Figure 1.4 for Divided Residential Subdivision Entrance cross section). b. In areas where a divided subdivision entry is constructed, the transition to the normal residential street width shall begin upstream or downstream of the first street intersection. No part of the transition shall occur within the intersection. c. Alternative design standards may be required for these types of subdivision entries if they are located within special overlay districts defined by the Town. 1-14 C. Minimum Right-Turn Storage and Transition Length: 1. Right-Turn Lane Storage: a. Right-turn lanes shall be required at every street intersection along 4 or 6 lane thoroughfares at the time of construction of each intersection. b. All right-turn storage areas shall be eleven feet (11') wide (except on 4LRD thoroughfares where a minimum width of ten feet (10') will be allowed). c. An additional ten feet (10') of ROW shall be provided with right-turn lanes. d. Right-turn lanes will be delineated by using buttons. e. Storage requirements listed in Table 1.6 are absolute minimums. Storage requirements may increase based upon actual and projected traffic demands. f. A tangent section of ten feet (10') shall be provided from the preceding driveway curb return to the transition of a right-turn lane. 2. Transition Length — The transition specifications for right-turn lane entrance areas are specified in Table 1.6. The variables used for the specification are shown in Figure 1.12. TABLE 1.6: Minimum Right-Turn Lane Design Requirements Type of Type of Turn Lane Length of Transition Specifications(2) Thoroughfare Thoroughfare Width ft Full-Width On At ( ) Turn Lane(ft)(1) Length(ft) R1(ft) R2(ft) 6LD, 4/6LD 4 or 6 lane 11 200 150 515 515 4LD 4 or 6 lane 11 150 150 515 515 6LD, 4/6LD, 4LD 3L, 2LC 11 150 110 280 280 6LD, 4/6LD, 4LD 2LN, 2LRN 11 100 110 280 280 4LRD All Types 10 100 110 280 280 NTTA Service All Types 11 200 150 515 515 Road (1) Measured from the intersecting thoroughfare ROW. (2) No driveways are permitted within the transition area. R2 Storage Length R 1 Lane Width Length of Transition FIGURE 1.12: Typical Right-Turn Lane Dimensions 1-15 D. Minimum Deceleration Lane Storage and Transition Length: 1. Deceleration Lane Storage: a. Deceleration lanes shall be provided at driveways on 4 or 6 lane thoroughfares where required by Section 1.05.(A.4). b. All deceleration lane storage areas shall be eleven feet (11') wide (except on 4LRD thoroughfares where a minimum of ten feet (10') will be allowed). c. Ten feet (10') of street easement, adjacent to ROW, shall be provided with deceleration lanes. d. Deceleration lanes will be delineated by buttons. e. Storage requirements listed in Table 1.7 are absolute minimums. Storage requirements may increase based upon actual and projected traffic demands. f. A tangent section of ten feet (10') shall be provided from the preceding driveway curb return to the transition of a deceleration lane. 2. Transition Length - The transition specifications for deceleration lane entrance areas are specified in Table 1.7. The variables used for the specification are shown in Figure 1.13. TABLE 1.7: Minimum Deceleration Lane Design Requirements Type of Type of Turn Lane Length of Full- Transition Specifications Thoroughfare Thoroughfare Width(s) Width Turn Lane On At (ft) (ftyl) Length(ft) R1(ft) R2(ft) 6LD, 4/6LD Non-Residential 11 80 110 280 280 Driveway 4LD Non Residential 11 60 110 280 280 Driveway 4LRD Non Residential 10 60 110 280 280 Driveway NTTA Service Non-Residential 11 80 110 280 280 Road Driveway (1) Measured from the curb return of the driveway. R2 Lane Width R1 Length of Storage Length Transition FIGURE 1.13: Typical Deceleration Lane Dimensions 1-16 E. Cost of Median Openings and Turn Lanes: 1. Median openings, left-turn lanes, and right-turn lanes constructed for residential streets and/or subdivision entrances shall be the responsibility of the developer and shall be paved to Town standards and inspected by the Town. 2. Median openings, left-turn lanes and deceleration lanes for Multifamily and non-residential developments shall be the responsibility of the developer and shall be paved to Town standards and inspected by the Town. 3. The Town shall require escrow of funds for such future improvements prior to final acceptance or Certificate of Occupancy, whichever occurs first. The escrow shall include all construction costs; engineering (7% of construction cost) and inspection (3% of construction cost). 1.04 ALLEY AND SERVICE ROAD DESIGN: A. Alley Intersections: 1. Alleys shall only intersect 3L, Residential 2LC, 2LN, and 2LRN thoroughfares. 2. If an alley and a Commercial 2LC or higher class thoroughfare are parallel and separated only by a landscape buffer, the alley shall turn away from that thoroughfare not less than one subdivision lot width or a minimum of forty feet (40') (whichever is greater) from the cross street as shown in Figure 1.14. 3. The ROW line of all alley intersections shall be a minimum of forty feet (40') or one subdivision lot width (whichever is greater) away from the ROW line of the nearest street intersection (See Figure 1.14). 4. All alley intersections with streets shall be perpendicular or radial, within a five degree (5°) tolerance, at the intersection of the ROW lines. 5. Alley offsets along residential streets shall be less than fifteen feet (15') or greater than seventy-five feet(75') measured from alley centerline to alley centerline. 6. Alleys shall not align with existing streets such as to create a four-way intersection. 7. Alleys shall not align across from future streets to create an intersection. 8. Internal alley to alley intersections shall be offset, from the centerline, a minimum of one hundred feet (100'). 1-17 Minimum of 40 Feet or One Subdivision ROW Lot Width 1 f Residential Street - - ROW Reference Sec.1.04.(A.3) a°'i Minimum of 40 Feet or Reference ro One Subdivision Sec.1.04.(A.2) > o Lot Width - - - \ TO to 25 Ft.Landscape Buffer Commercial 2LC or Higher Class Thoroughfare FIGURE 1.14: Minimum Distance from Intersection for Parallel Alley B. Alley Radius - Alley radii at street intersections shall not be less than fifteen feet (15') (See Figure 1.15). 1. Alley Intersecting Alley Radius —The radius shall be measured from the ROW and vary based upon the alley ROW intersection angle listed in Table 1.8. TABLE 1.8: Alley Intersecting Alley Radius Alley ROW Intersection Angle Minimum Required ROW Radius(ft) 1°-40° 70 41°-70° 50 71°-90° 40 --------------- ------- ----> 90° 50 C. Alley ROW Width - The alley ROW width shall be fifteen feet (15') for residential alleys and twenty feet (20') for non-residential alleys. D. Alley Pavement Width - The alley pavement width shall be ten feet (10') for residential alleys and twelve feet (12') for non-residential alleys, except near street intersections as shown in Figure 1.15. E. Alley Pavement Thickness — The thickness shall be a minimum of 6" with pavement strength and reinforcement as required in Section 1.02.(B.5). 1-18 Street 15-16 Ft. Pavement Width 71?115Ft. Minimum Radius ROW 20 Ft.' a) 15-20 Ft. ROW Width N 10-12 Ft. Pavement Width FIGURE 1.15: Alley Dimensions F. Rear Alley Frontage -The minimum alley rear frontage shall be twenty feet (20'). G. Alley Speed Limits -The speed limit in alley ways shall be ten miles per hour (10MPH). H. Alley Visibility Obstructions: 1. No fence, wall, screen, sign, structure, or foliage of hedges, trees, bushes, or shrubs shall be erected, planted or maintained in any alley ROW. 2. Foliage of hedges, trees, bushes, and shrubs planted adjacent to the alleys ROW shall be maintained such that the minimum overhang or encroachment shall be fourteen feet (14') above the alley surface one foot (1') outside the edge of the pavement. 1.05 DRIVEWAY DESIGN: A. Introduction - Driveway design standards are needed to provide safe and efficient vehicular access to and from the public street system, to provide public street capacity for accommodating peak traffic volumes of public streets, to maintain smooth traffic flow, and to maintain street ROW and drainage. The intent of driveway design standards is to achieve the following: 1. Prohibit the indiscriminate location and spacing of driveways while maintaining reasonable vehicular access to and from the public street system. 2. Reduce conflicting turning movements and congestion thereby reducing vehicular accidents. 3. Maintain and enhance a positive image for the attraction of new, high quality, residential and non-residential development in the Town. 4. Provide right-turn and deceleration lanes for all streets and driveways along Preston Road, US380, and the frontage roads of the Dallas North Tollway. Along all other 4 or 6 lane thoroughfares, deceleration lanes are required only for driveways served by a median opening. Deceleration lanes will not be required at a driveway located between one hundred feet (100') and one hundred seventy feet (170') downstream of a 4 or 6 lane intersection (see Figure 1.16). 1-19 B. Definition of Driveway Types: 1. Residential Driveway - Provides access to a single-family residence, duplex, or multifamily building containing four or fewer dwelling units. These drives shall intersect Residential 2LC, 2LN, and 2LRN thoroughfares only. 2. Non-Residential Driveway: a. Commercial Driveway - Provides access to an office, retail or institutional building, or multifamily building having more than four dwelling units. It is anticipated that such buildings will have incidental truck service. Commercial drives shall access 3, 4 or 6 lane thoroughfares only. b. Industrial Driveway - Serves truck movements to and from loading areas of an industrial facility, manufacturing, warehouse, or truck terminal. A retail development may have one or more driveways specially designed, signed, and located to provide access for trucks. These types of driveways shall be considered industrial driveways. (Driveways to industrial plants whose principle function is to serve administrative or employee parking lots shall be considered commercial driveways.) Industrial drives shall not access Residential 2LC, 2LN, or 2LRN thoroughfares. 3. Standard Driveway - Provides two-way access at a single, undivided curb opening. 4. One-Way Driveway - Provides inbound or outbound access and can only be permitted when the orientation of on-site circulation and parking layout clearly utilize the driveway for one- way movements. 5. High Capacity Driveways - Intended to provide two-way access with geometric provisions which more adequately respond to greater driveway volumes and/or access limitations than standard driveways. These provisions include increased width and/or internal storage. Median divider and/or deceleration lanes may also be required. C. General Design Parameters: 1. The centerline angle for a driveway approach shall be ninety degrees (90°) to the street curb line for all driveways. 2. Driveways shall not be permitted in the transition area of any right-turn lane or deceleration lane. 3. Driveways that intersect at a mid-block median shall have the driveway centerline intersect with the midpoint of a median opening (measured nose-to-nose). 4. Driveway restrictions can be required by the Town Engineer to ensure adequate circulation. 5. Driveway elevations at the ROW line shall be a minimum of six inches (6") above the street gutter. A residential driveway that intersects an alley shall be three inches (3") above the edge of the alley pavement at the ROW line. 6. Cross access is required between adjacent retail, office and commercial properties. 7. Driveway grades in a fire lane shall not exceed six percent (6%) either longitudinally or laterally to accommodate emergency vehicle access. 8. Differential grades on driveways shall not exceed twelve percent (12%). 1-20 D. Driveway Width -The width of a driveway refers to the width of pavement at the property line and is measured where the curb return radii ends perpendicular to the street curb or edge of pavement. The minimum and maximum widths of driveways are listed in Table 1.9. TABLE 1.9: Minimum and Maximum Driveway Widths Driveway Type Land Use Width in Feet(face to face) . _ Minimum (ft) Maximum(ft) Residential 10 24 Standard Drive Commercial/Multifamily 24 30 Industrial 30 40 Residential (circular) 10 16 One-Way Drive Commercial 16 24 Industrial 24 24 Entrance Lane 16 24 High Capacity Drive for Exit Lanes:One 12 16 Non-residential Uses Two 24 24 Three 30 30 Driveway Medians (non-residential/multifamily uses) 4 11 Notes: 1. A residential driveway width of thirty-two feet (32') may be allowed to an alley if the garage faces onto the alley. 2. The maximum width for service station driveways shall be forty feet(40'). 3. Driveways that serve as a fire lane shall be a minimum of twenty-four feet(24') in width. E. Driveway Radius: 1. All driveways intersecting dedicated streets shall be built with a circular curb radius connecting the six-inch (6") raised curb of the roadway to the design width pavement of the driveway. 2. Driveway radii shall fall entirely within the subject property so as to begin at the street curb, at the extension of the property line. 3. Table 1.10 presents the minimum and/or maximum standards to be applied in designing and locating driveways on public streets. 4. High capacity driveways shall meet the same standards as those defined in Table 1.10. F. Driveway Spacing: 1. Driveways shall be spaced at distances sufficient to ensure that conflicting movements do not overlap at adjacent driveways or at offset driveways on opposite sides of the street. 2. Spacing between driveways should be measured along the property line from the edge of one driveway to the closest edge of the next driveway and not from centerline to centerline. 3. The minimum spacing between driveways is a function of street classification and shall be as listed in Table 1.10. 4. The driveway spacing from a railroad crossing shall be a minimum of fifty feet (50') from the railroad ROW. 1-21 TABLE 1.10: Driveway Design Requirements Thoroughfare Residential Commercial/ Industrial Criteria Multifamily Driveway Classification Driveway (ft) Driveway (ft) (ft) Major: 6LD, 4/6LD -- 20-30 20-30 Driveway Curb Minor: 4LD, 4LRD -- 20-30 20-30 Radius 3L, Commercial 2LC -- 20-30 20-30 Residential 2LC 5-10 20 -- Local: 2LN, 2LRN 5-10 -- -- Major: 6LD, 4/6LD -- 240 240 Minimum Minor: 4LD, 4LRD -- 200 200 Driveway Spacing 3L, Commercial 2LC -- 90 90 Along Roadway Residential 2LC 20 max.of 1 drive -- (edge to edge) Local: 2LN, 2LRN 20 -- -- Minimum Distance Major: 6LD, 4/6LD -- 75/ 100(2) 75/ 100(2) between Minor: 4LD, 4LRD -- 75/ 100(2) 75/ 100(2) Intersection and 3L, Commercial 2LC -- 50/ 50 50/ 50 Driveway Residential 2LC 20/ 20 100/ 100 _ -- (driveway edge to intersecting 10/10 from ROW) ' Local: 2LN, 2LRN tangent to edge -- -- of drive (1) upstream / downstream distance to intersection. (See Figure 1.16) (2) a driveway can be installed without a deceleration lane as long as it is located no more than one hundred seventy feet (170') from the intersection (measured from the intersecting ROW to the downstream edge of the driveway). 4. A residential land use shall be allowed a maximum of one (1) driveway opening per lot, tract, or parcel except as provided by the approval of a circular driveway. 5. To minimize the number of curb cuts along public roadways, joint or shared access is encouraged for residential driveways and required for commercial driveways. Shared access drives shall conform to the following standards: a. Residential: no less than ten feet (10') of the total driveway width (20' min. — 24' max.) shall be located on each property. b. Commercial/Industrial: no less than twelve feet (12') of the total driveway width (24' min. — 36'max.) shall be located on each property. c. Joint access drives for commercial/industrial developments shall include full drive width and access pavement and be built at the same time as a development. d. The spacing and location of driveways shall be related to both existing adjacent driveways and those shown on approved development plans. 1-22 Street 1` 1 Direction of Travel Direction of Travel ROW > ct ROW (Min.50') 3 (Min.75') ` (Min. 100') ~ _ Upstream Downstream Distance Distance Ca (Max. 170')* *For a driveway without a deceleration lane on a street where one would be required otherwise FIGURE 1.16: Distance Between Driveway and Intersection G. Distance Between Driveway and Intersection: 1. Adequate distance between cross street intersections and access drives shall be provided to ensure intersection/driveway conflict areas are minimized. 2. Table 1.10 defines the upstream and downstream distance from an intersection as a function of street classification. H. Deceleration Lanes: 1. Deceleration lanes for right-turns into driveways will ease the negative impact a driveway will have on traffic flow, driveway conflict points and safety due to speed differential. 2. One driveway may be located within the full-width storage portion of a right-turn lane at a public street intersection. Such a driveway shall be located a minimum of seventy-five feet (75') in advance of the intersecting ROW, and a minimum of fifty feet (50') of storage length shall be provided in advance of the driveway (see Figure 1.16). 3. The developer shall be responsible for the design, ROW adjustment of utilities, and construction costs of any auxiliary and deceleration lane required as a condition of a driveway permit. 4. A ten-foot (10') street easement shall be provided for deceleration lanes for non-residential developments. 5. Refer to Table 1.7 for deceleration lane design standards. 1-23 I. Driveway Storage Lengths: 1. On-site internal storage shall be provided at all non-residential and multifamily driveways for queuing of vehicles off-street, to minimize congestion, and increase safety both on the public street and within the driveway. 2. Internal storage requirements shall be based on the total number of parking spaces accessible by the affected driveway. 3. Internal storage length shall be measured from the ROW line to the first aisle or parking stall that intersects with inbound traffic. If inbound traffic and outbound traffic are separated by a median for the required storage distance, a parking aisle can connect to the outbound portion of the driveway closer to the street (as long as a minimum of twenty-five feet (25') is maintained between the aisle and the ROW line). 4. Table 1.11 presents internal storage requirements. TABLE 1.11: Minimum Driveway Storage Lengths Storage Required (ft) Parking Spaces Multifamily / Commercial Uses Industrial Land Uses per Driveway Non-Median Non-Median Median • Opening Median Opening Opening Opening Less than 25 25 25 25 25 25-50 25 40 25 40 51-100 25 40 40 40 101-200 40 80 40 60 More than 200 100 100 40 100 J. Driveways for Gated Developments: 1. Residential/Multifamily: a. Gated developments shall have a median divided street that will allow for a vehicular turn-around prior to the gate in the event that access is denied. b. The turn-around shall be a minimum of eighteen feet (18') in width. c. Entry gates shall be set back from the ROW a minimum of one hundred thirty-five feet (135') to provide stacking space to the card reader (or first stop) of a minimum of one hundred feet (100') to allow the longest queue of vehicles expected to access the gate. d. The drives shall be a minimum of twenty-four feet (24') in width with driveway curb radii of thirty feet(30'). See Figure 1.17. e. The hinge point of the gate shall be a minimum of eighteen inches (18") behind back of the curb. The gate shall open to twenty-four inches (24") behind back of curb. f. Gates shall be equipped with both opticom and knox box for emergency access. g. Gates shall not encroach on sidewalks. 1-24 2. Other Non-Residential: a. Gated developments shall have a median separating ingress and egress traffic flow allowing for a vehicular turn-around prior to the gate in the event that access is denied. b. The turn-around shall be a minimum of eighteen feet(18') in width. c. Entry gates shall be set back from the ROW or fire lane a minimum of seventy-five feet (75') to provide stacking space to the card reader (or first stop) of a minimum of forty feet (40') to allow the longest queue of vehicles expected to access the gate. d. The drives shall be a minimum of twenty-four feet (24') in width with driveway curb radii of thirty feet (30'). See Figure 1.17. e. The hinge point of the gate shall be a minimum of eighteen inches (18") behind back of the curb. The gate shall open to twenty-four inches (24") behind back of curb. f. Gates shall be equipped with both opticom and knox box for emergency access. g. Gates shall not encroach on sidewalks. h. Alternate standards may be required based on the results of a Traffic Impact Analysis (TIA). 3. Individual gated single-family residences — Gate shall have a minimum setback of twenty feet (20') from the ROW to provide space for at least one vehicle to wait while accessing the gate. 100'ROW 15'R 20R 20R 12' _ _ _ _ _ _ _ 12' 10'x10'ROW Clip AN 10'x 10'ROW Clip T - - — — Building Line Building Line See Section 1.05(J) Gates Located at or Behind Building Line for Setback - Requirements I 18' I � I Reader/Keypad First Stop Minimum (100'-Residential/Multi-Family) Stacking Distance (40'-Other Non-Residential) 250'Minimum 25'x 25' Centerline Radius 5' 5, ROW Clip 25'x 25'ROW Clip Landscape ROW J 11, — — Landscape ROW 12' 30'R 12' 30 R 1 100'Storage 110'Transition 10' f 60'Min 100'Transition 150'Storage 70'Max FIGURE 1.17: Gated Entrance Detail 1-25 K. Non-Conforming Driveways: 1. All nonconforming driveways on a lot, tract, parcel or site shall be allowed to remain in place until the occurrence of one or more of the following events: a. A change in use, or an increase in intensity of use, occurs such that the site requires a ten percent (10%) increase in required parking spaces. b. Addition of parking spaces. c. Any modification that changes the design or function of the existing driveway. d. The addition of a median opening on the public street by a developer. All driveways that are served by the new median opening shall comply with the requirements of these standards. 2. Upon the occurrence of the events described, the nonconforming status of the driveway shall cease and the driveway either reconstructed in accordance with this ordinance, or eliminated. 1.06 SIDEWALK AND LOCATION DESIGN: A. Definition of Sidewalk - A sidewalk is defined as that paved area in a street ROW between the curb lines or the edge of pavement of the roadway and the adjacent property lines for the use of pedestrians. The maximum grade of the sidewalk shall be one-half-inch (1/2") per foot. The maximum cross-fall of the sidewalk shall be one-quarter-inch (1/4") per foot. Sidewalks shall conform to ADA requirements, that currently exist, and to the following standards: 1. Zoning Classification Requiring Sidewalks - Concrete sidewalks designed and located according to Town standards shall be constructed along all streets in all zoning classifications except agriculture uses in agricultural zoned areas. Non-residential and multifamily sidewalks shall be built at the time of lot development. Should it be impractical to install the sidewalk at that time, funds for the sidewalk construction shall be placed in escrow with the Town for use when the Town determines sidewalks are needed. Payment of such escrow shall be made prior to final acceptance of residential uses or certificate of occupancy for non- residential and multifamily uses. 2. Residential Areas (Single Family and Duplex) - A concrete sidewalk, four feet (4') in width, shall be located within the street ROW, two feet (2') from the ROW line, unless pre-existing physical encroachments (e.g., utility infrastructure or trees) dictate otherwise. Sidewalks and parkways (curb to ROW) shall be graded at one-quarter-inch (1/4") per foot above the top of the street curb. Sidewalks for residential lots shall be constructed by the homebuilder. Sidewalks for amenity centers or open space lots shall be constructed by the developer. 3. Non-Residential Areas and Apartment Complexes - A concrete sidewalk, four feet (4') in width, shall be located in street ROW not less than two feet (2') from the ROW line. If other materials are placed in the ROW between the sidewalk and curb, the material shall meet Town specifications and be of a color and texture distinctly different from the sidewalk and specified on the site plan. 4. Meandering Sidewalks - Sidewalk easements adjacent to the standard ROW will be required, if necessary, for meandering sidewalks. The outside edge of the sidewalk shall meander in and out of the sidewalk easement and, at its closest point to the street, shall be located not less than five feet (5') from the back-of-curb. Sidewalk easements shall provide a minimum clearance of two feet (2') beyond the outside edge of the sidewalk. 1-26 5. Exceptions - If it should be necessary to construct a sidewalk immediately adjacent to the street curb line (or if the outside edge of a four foot sidewalk will come within five feet (5') of the street curb), the sidewalk shall be a minimum of six feet (6') in width. If the required sidewalk is to be placed outside of the street ROW, it must be placed in a sidewalk easement. Approval of planned exceptions and sidewalk easements shall be made at the time of site plan or plat approval. 6. Areas with Screening Walls - In areas where a screening wall is provided, a meandering sidewalk is encouraged and shall not encroach any closer than eighteen inches (18") from the wall. 7. Sidewalks on Bridges - All street bridges shall have a sidewalk constructed on each side of the bridge. The sidewalk shall be a minimum of six feet (6') wide with a parapet wall provided a minimum of two feet (2') behind the curb of the thoroughfare. A standard pedestrian bridge rail protecting the sidewalk shall be provided on the outside edge of the bridge. See Figure 1.18. 2' 6' Q THRU / � I PEDESTRIAN HAND RAIL PARAPET WALL SIDEWALK FIGURE 1.18: Bridge Parapet Wall and Pedestrian Rail S. Sidewalks Under Bridges - When new bridges are built as a part of the construction of a roadway or the reconstruction of a roadway and a pedestrian crossing is needed, an eight- foot (8') sidewalk will be built as a part of the embankment design underneath the bridge structure. 9. Sidewalks on Culverts—All culvert crossings shall have a sidewalk constructed on each side of the culvert. The sidewalk shall be a minimum of six feet (6') wide with a standard pedestrian hand rail as shown in Figure 1.18 provided on the outside edge of the culvert. Parapet wall may be required by the Engineering Department. 10. Access to Cul-de-sacs from Adjacent Streets - To promote a pedestrian friendly environment, a sidewalk shall be provided between cul-de-sacs and adjacent streets. 1.07 PUBLIC RIGHT-OF-WAY VISIBILITY REQUIREMENTS: A. Adequate sight distance at the intersection of a thoroughfare and a proposed thoroughfare/driveway/alley must be ensured. This sight distance is provided through the use of a Corner Visibility Triangle and/or a Sight Line Triangle. Corner Visibility Triangles shall be dedicated as ROW and Sight Line Triangles shall be identified and dedicated as Visibility, Access and Maintenance Easements (VAM's). In addition, a Sight Line Triangle must also be provided for the following cases: 1. Where a driveway, alley, or any thoroughfare that is controlled by a stop sign intersects with an uncontrolled thoroughfare. 2. On any signalized intersection approach where right-turn on red operation is permitted, a sight line triangle must be provided for the right turn driver. 1-27 B. Corner Visibility Triangle Defined: 1. The corner visibility triangle is defined at an intersection by offsetting the two ROW lines from their point of intersection to a distance as shown on Table 1.12. These two points are then connected with an imaginary line to form the corner visibility triangle as shown in Figure 1.19. If there are no curbs existing, then the triangular area shall be formed by offsetting the property lines for a distance of thirty feet(30') from their point of intersection. TABLE 1.12: Corner Visibility Triangle Distances Type of Thoroughfare Type of Thoroughfare Distance On At (X) 4 or 6 lane All Types 25' • 3L, Commercial 2LC 3L, 2LC 25' 3L, Commercial 2LC 2LN, 2LRN 10' Residential 2LC, 2LN, 2LRN Residential 2LC, 2LN, 2LRN 10' NTTA All Types 25' X X ROW - ROW X X ROW ROW Corner Visibility Triangles FIGURE 1.19: Corner Visibility Triangle for an Intersection 1-28 2. Where alleys intersect residential 2LN or 2LRN thoroughfares, the corner visibility triangle is measured as fifteen feet (15') along the residential street ROW and five feet (5') along the alley ROW from the point of intersection. These two points are then connected with an imaginary line to form the corner visibility triangle as shown in Figure 1.20. The alley corner visibility triangle shall be dedicated as ROW. c.1 15.0 Residential Street ( ROW 5.0 I � FIGURE 1.20: Corner Visibility Triangle for an Alley C. Sight Line Triangle Defined: 1. The sight line triangle is formed by first extending a line along the center line of the proposed side street or driveway that begins at the tangent curb of the existing thoroughfare and extends to its endpoint fifteen feet (15') into the proposed side street or driveway. For the sight line triangle to the left, construct a second imaginary line that is parallel to and five feet (5') out from the existing thoroughfare's curb that begins at the centerline of the side street and continues to the left for a distance L to its endpoint. To complete the sight line triangle, connect the endpoints of the first two lines as shown in Figures 1.21 and 1.22. In the case of the sight line triangle to the right, the second imaginary line is parallel and five feet (5') out from the nearest edge of the conflicting traffic flow (or adjacent median in the event of a divided thoroughfare). It begins at the centerline of the side street and continues to the right for a distance R to its endpoint (See Figures 1.21 and 1.22). 1-29 L R 5 Ft. c, /%% /5 Ft. // 15 Ft. FIGURE 1.21: Sight Line Triangle for an Undivided Thoroughfare — -5 FL 15 Ft. FIGURE 1.22: Sight Line Triangle for a Divided Thoroughfare 2. The distance to the driver's eye for driveways or side streets that intersect a thoroughfare is fifteen feet (15') from the intersecting curb line as shown in Figures 1.21 and 1.22. 3. In the case where the thoroughfare contains existing horizontal curvature, the distances L and R must be measured along the horizontal curve. 4. According to the American Association of State Highway and Transportation Officials (AASHTO), the minimum lengths of the distances L and R are equal. The minimum sight line distances, L and R, vary according to the design speed and width of the thoroughfare that will be accessed by a vehicle stopped on the side street, as shown in Table 1.13. 1-30 TABLE 1.13: Minimum Sight Line Triangle Distances") Minimum Sight Distance to Left and Right, L and R(ft) Design Speed 2-lane divided(2) 4-lane divided(2) V(MPH) 2-lane or or 6-lane divided(2) undivided 4-lane undivided 6-lane undivided 25 280(3) 295 315 335 30 335 355 375 400 35 390 415 440 465 40 445 475 500 530 45 500 530 565 600 • 50 555 590 625 665 (1) Source AASHTO Green Book — Chapter 9. Distances based upon design speed and width of the thoroughfare that will be accessed by a vehicle stopped on the side street. (2) These calculations assume a median width equivalent to one travel lane. If the median is wider than a travel lane, add 30 feet of sight distance for every 12 feet of additional median width. (3) L can be 150 feet with approval by the Town Engineer or his/her designee. D. Landscaping and Obstruction Requirements for Corner Visibility and Site Line Triangles: 1. No fence, wall, screen, sign, structure, foliage, hedge, tree, bush, shrub, berm, driveway, parking space, drive aisle, or any other item, either man-made or natural shall be erected, planted, or maintained in a position that will obstruct or interfere with a driver's clear line of sight within both the corner visibility and sight line triangle (i.e., VAM's). 2. Vision at all intersections where streets intersect at or near right angles shall be clear at elevations between thirty inches (30") and nine feet (9') above the average gutter elevation within each triangle. E. Landscape Plan Requirements: 1. A landscape plan is required that shows the plan/profile of the street on both sides and the median, where necessary, of each proposed drive/street to the proposed development with the grades, curb elevations, proposed street/drive locations, and all items (both natural and man-made) within both the corner visibility and sight line triangles. 2. This landscape plan shall be provided with all site plans and engineering plans that are submitted for review/approval. This profile shall show no horizontal or vertical restrictions (either existing or future) within the corner visibility and sight line triangles. 3. All landscape plans shall show all items as required by the Parks and Recreation Department and Planning Department. F. Rights-of-Way Obstructions Outside the Site Line Triangles: 1. Fences, walls, screens, signs and other structures shall conform to the Comprehensive Zoning and Sign Ordinances of the Town. 2. Foliage of hedges, trees and shrubs in ROW which are not governed by Prosper's Comprehensive Zoning Ordinance, or the above triangles shall be maintained such that the minimum overhang above a sidewalk shall be seven feet (7') and the minimum overhang above a street shall be fourteen feet (14'). 1-31 3. All other areas within ROW shall be clear at elevations between thirty inches (30") and nine feet(9') above the average gutter. 4. Plants in the ROW that will grow over thirty inches (30") (when mature) above the adjacent street's curb shall conform to all of the above requirements, where applicable. All landscape plans shall show all items as required by the Parks and Recreation Department and Planning Department, including: a. The locations and type of such plants. b. The prescribed corner visibility and sight line triangles. c. Ground elevations or spot elevations as necessary, to avoid conflicts, will be shown by contour lines within both triangles. d. No plantings or berms over thirty inches (30") above the adjacent gutter elevation are allowed in the median for the length of the left turn storage. e. Single trunked trees within the triangles and in the median shall be allowed and spaced so as to not cause a "picket fence" effect. Because of the large variation of ways in which trees can be planted, the spacing shall be decided upon by Town Engineer or his/her designee and the developer at the time of review of the landscape plans. Any other item that obstructs these lines so as to interfere with the above requirements shall not be allowed. G. Abatement: 1. The Town Engineer or his/her designee shall have the authority to determine whether any such fence, wall, screen, hedge, tree, bush, shrub, sign or structure, as erected, planted or maintained, constitutes a public hazard or public nuisance in violation of the provision of this ordinance. Upon determination, he/she shall cause to be issued a written notice to the owner or lessee of the property demanding that corrective action be taken within ten (10) days of the date the notice is mailed. 2. Following written notice, the Town of Prosper may abate the hazard or nuisance and assess the property owner reasonable charges for labor. 3. Under conditions which pose an immediate threat to the public's health, safety, or general welfare, the Town Engineer or his/her designee may require immediate corrective action. H. Exceptions - The provisions of the Thoroughfare and Circulation Design Requirements shall not apply to, or otherwise interfere with, the following: 1. Placement and maintenance of traffic control devices under governmental authority and control. 2. Existing and future Town, State and Federal Regulations. 1.08 TRAFFIC CALMING GUIDELINES: A. Introduction: 1. Traffic Calming, a concept that dates back to the 1960s and 70s, has been implemented more extensively throughout the United States during the 1990s. The primary purpose of traffic calming is to decrease speeds and reduce cut-through traffic volumes. The Institute of Transportation Engineers (ITE) defines traffic calming as follows: 1-32 "Traffic Calming is the combination of mainly physical measures that reduce the negative effects of motor vehicle use, alter driver behavior and improve conditions for non-motorized street users." 2. Urban sprawl and traffic congestion continue to increase in the United States. As a result, speeds and cut-through volumes on local streets and collectors will continue to increase unless traffic calming measures are put in place or new local and collector thoroughfares are designed with traffic calming in mind. 3. The Thoroughfare and Circulation Design Requirements and Subdivision Ordinances are intended to provide design and access requirements that are proactive in addressing traffic calming issues in residential areas. In instances where problems exist that can be addressed by traffic calming, a specific process will be used to identify the problem and potential solutions. 4. Traffic control devices such as STOP Signs and speed limit signs are regulatory measures that require enforcement. Traffic calming measures, however, are intended to be self-enforcing. B. Traffic Calming Process - The traffic calming process contains steps that include the three E's commonly found in traffic calming programs. These E's are Education, Enforcement and Engineering. In many instances, applying the Education and Enforcement steps will solve the problem without implementing a more costly engineering solution. The traffic calming process will use the following steps: 1. Neighborhood must identify a problem and bring it to the Town's attention with a petition signed by 75% of the property owners along the street. 2. The Town will conduct a study, funded at the property owners' expense, to determine the extent of the reported problem. 3. The Town will examine the results of study. 4. If the study indicates that a problem exists, the Town will identify if there are additional stakeholders in solving the problem. These additional stakeholders will typically include emergency services and the school district. 5. If speeding problem exists, the Town will then: a. Identify possible causes. b. Work with the neighborhood to raise awareness to the problem (Education). c. Increase the enforcement level after the education process (Enforcement). d. Conduct another study to determine if Education and Enforcement have solved the problem. e. If a speeding problem still exists, the Town will then: (i) Determine the best traffic calming measure to apply (Engineering). (ii) Determine whether the solution should be a temporary installation or permanent installation. (iii) Conduct an after study to see if the measure has had the desired effect. 1-33 6. If a cut-through problem exists, the Town will then: a. Identify possible causes. b. Examine the area roadway network to determine the best solution. c. Work with surrounding neighborhoods to implement a solution. This step is necessary because traffic calming measures that address this problem may move the cut-through traffic to another neighborhood street. d. Conduct an after study to determine if the solution was effective. C. Role of Emergency Services and School District—The traffic calming process must involve Fire and Rescue, Police and the School District (bussing). It is recommended that these agencies play an advisory role. Some measures may delay emergency response time. It is imperative that each neighborhood realizes that this is a trade-off when implementing traffic calming measures. All traffic calming measures must be designed to accommodate emergency vehicles and school buses. D. Traffic Calming Measures — Below is a list of traffic calming solutions for speed related problems and cut-through traffic problems. The solutions are listed in no particular order. 1. Potential Solutions for Speed Related Problems: a. Chokers — midblock b. Neckdowns—at intersection c. Neighborhood speed watch program d. Realigned intersections e. Medians f. Traffic circles/roundabouts g. Lateral shifts h. Textured pavements i. Chicanes j. Speed humps Note: STOP signs are not intended for speed control. Studies have shown that installation of STOP signs to control speed actually increase the speeds measured at midblock locations between STOP signs. 2. Potential Solutions for Cut-Through Traffic Related Problems: a. Diverters b. Median barrier c. Turn restrictions d. Street closures 1-34 1.09 FRONTAGE ROAD DESIGN: A. Frontage roads are typically found adjacent to existing or planned freeway type facilities. B. Frontage roads are considered 6LD thoroughfares and should be designed to the 6LD standards set forth in this document. C. Access to frontage roads shall also conform to the standards set forth for 6LD thoroughfares. In addition, the following access restrictions apply to frontage road design: 1. Exit Ramp Restrictions: a. No driveway shall be located less than fifty feet (50') in advance of the concrete curb gore of an exit ramp. b. No driveway shall be located less than four hundred feet (400') beyond the concrete curb gore of an exit ramp. 2. Entrance Ramp Restrictions: a. No driveway shall be located less than two hundred feet (200') in advance of the concrete curb gore of an entrance ramp. b. No driveway shall be located less than fifty feet (50') beyond the concrete curb gore of an entrance ramp. 1.10 TRAFFIC SIGNAL DESIGN AND INSTALLATION REQUIREMENTS: A. Introduction: 1. Traffic signals that are properly justified, designed, operated, and effectively located may result in one or more of the following: a. Assign ROW to assure an orderly movement of traffic at an intersection. b. Provide progression for a platoon of vehicles along a given route. c. Interrupt heavy traffic to allow cross-street traffic and pedestrians to cross or enter the main street flow. d. Increase the capacity of an intersection or certain traffic movements at the intersection. e. Reduce the frequency of occurrence of certain types of accidents. 2. Although traffic signals may be warranted they may not always result in the desired effects listed above. If they are improperly designed, operated, or maintained and are not located in an effective manner they can: a. Increase accident frequency (especially rear end accidents). b. Cause excessive delay for motorists and pedestrians. c. Cause disregard of other signal indications. 1-35 d. Cause cut-through traffic on nearby collectors and residential streets B. Warrant Criteria: 1. To justify the installation of a traffic signal, Part IV in the Texas Manual of Uniform Traffic Control Devices(TMUTCD) should be followed. It not only describes the warrants for a signal installation, but also provides guidelines and requirements for the actual design and operation of a traffic signal. 2. Engineering studies must be conducted in order to assess whether a particular location satisfies the warrant criteria listed in the TMUTCD. These studies may include one or more of the following: a. Traffic volume counts b. Pedestrian volume counts c. Delay studies d. Speed studies e. Gap studies f. Diagram of physical conditions g. Accident studies 3. The TMUTCD states the following concerning the evaluation of the warrant criteria. "Traffic control signals should not be installed unless one or more of the signal warrants in this manual are met. The satisfaction of a warrant or warrants is not in itself justification for a signal. Information should be obtained by means of engineering studies and compared with the requirements set forth in the warrants. The engineering study should indicate the installation of a traffic signal will improve the overall safety and/or operation of the intersection. If these requirements are not met, a traffic signal should neither be put into operation nor continued in operation (if already installed)." C. Signal Spacing: 1. Signal spacing plays a very important part in being able to provide progressive flow for a platoon of traffic. Ideally, as the desired speed of a platoon increases, the signal spacing should also increase. Therefore, signal spacing on major thoroughfares should be larger than the signal spacing found on minor thoroughfares and collectors. 2. Factors that affect signal spacing include platoon speed and traffic signal cycle length. The platoon speed is the speed at which a group of vehicles travel between signalized intersections. The traffic signal cycle length is the time it takes for the traffic signal to complete a full sequence of signal indications. A summary of possible signal spacing requirements based on platoon speed and cycle length is shown in Table 1.14. D. Emergency: 1. Opticom detectors shall be provided on all traffic signals for use by emergency vehicles. 1-36 E. Conduit: 1. Two (2) four-inch (4") conduit rings with pull boxes shall be installed around an intersection whenever a major thoroughfare, minor thoroughfare, or collector intersects a roadway having a status of collector or higher. These conduits shall be used for future traffic signal communications, video monitoring and communications for Town services. 2. A two-inch (2") conduit with pull boxes shall be installed across median openings and intersections along every 4 or 6 lane thoroughfare. This conduit shall be used for future street lighting. TABLE 1.14: Sample Signal Spacing Requirements Cycle Platoon Signal Spacing (feet) Length Speed Two-way Progression Pattern __ (sec) (MPH) Alternate Double Alternate 60 30 1320 660 70 30 1540 770 80 30 1760 880 90 30 1980 990 100 30 2210 1100 110 30 2430 1210 120 30 2650 1320 60 35 1540 770 70 35 1800 900 80 35 2060 1030 90 35 2320 1160 100 35 2570 1290 110 35 2830 1410 120 35 3090 1540 60 40 1760 880 70 40 2060 1030 80 40 2350 1180 90 40 2650 1320 100 40 2940 1470 110 40 3230 1620 120 40 3530 1760 60 45 1980 990 70 45 2320 1160 80 45 2650 1320 90 45 2980 1490 100 45 3310 1650 110 45 3640 1820 120 45 3970 1980 1-37